Maintenance Plans

Our Maintenance plans

✅ Basic Comfort Plan

Includes:

  • 1 Maintenance Visit per Year (Customer’s Choice: Heating or Cooling)
  • 15-Point System Inspection
  • Standard Air Filter Replacement (1” filter)
  • Electrical Component Check
  • Thermostat Calibration Check
  • Drain Line Flush & Inspection
  • Priority Scheduling (within 48 hours)

Benefits:

    • Extend equipment life
    • Prevent costly breakdowns
    • Maintain energy efficiency
$149/year

🌿 Clean Air Plan

Includes:

  • 2 Maintenance Visits per Year (Spring & Fall)
  • 21-Point System Inspection
  • Standard Filter Replacement (1” filter)
  • Drain Line Cleaning
  • Electrical Safety Inspection
  • Airflow Check & Duct Inspection
  • Light Coil Rinse (outdoor unit)
  • Priority Scheduling (within 36 hours)
  • 10% Discount on Repairs

Benefits:

  • Cleaner indoor air
  • Early detection of issues
  • Reduced utility costs
$249/year

⚙️ Performance Plus Plan

Includes:

  • 2 Seasonal Tune-Ups (Spring & Fall)
  • 25-Point System Performance Inspection
  • Filter Replacement (up to 2” filters)
  • Indoor & Outdoor Coil Cleaning
  • Blower Motor & Capacitor Testing
  • Refrigerant Pressure Check
  • Full Drain Line Service & Flush
  • 15% Discount on Repairs
  • No After-Hours Fees
  • Priority Scheduling (within 24 hours)

Benefits:

  • Maximize equipment performance
  • Lower energy bills
  • Peace of mind for seasonal changes
$299/year

🛡️ Total Protection Plan

Includes:

  • 2 Full Maintenance Visits
  • 30-Point Comprehensive Inspection
  • Filter Replacements (up to 4” filters)
  • Full Coil Cleaning (indoor & outdoor)
  • Blower Motor & Fan Cleaning
  • Electrical Panel Inspection & Tightening
  • Full Drain Service
  • Up to 1 lb. Refrigerant Top-Off (if needed)
  • Same-Day Emergency Service
  • 20% Discount on All Repairs
  • $0 Diagnostic Fees (Mon–Sat)

Benefits:

  • VIP service response
  • Preventative care that saves $$$
  • Ideal for high-use systems in Florida
$399/year

🧰 Commercial Care Plan

Includes:

  • 2–4 Visits per Year (based on usage)
  • Full System Audit & Inspection
  • Filter Replacements (customized to unit size)
  • Belt & Pulley Inspection (if applicable)
  • Drain Line Flushing
  • Thermostat & Control Calibration
  • Rooftop Unit Cleaning (if applicable)
  • Priority Emergency Response
  • 15% Off Parts & Labor

Benefits:

  • Keep operations running
  • Reduce emergency breakdowns
  • Energy savings & system longevity
$499/year

30‑Point Comprehensive System Inspection

  1. Thermostat Calibration: Verify accurate temperature sensing and proper operation.
  2. Safety Controls Check: Test high‑limit switches, flame sensors, and other safety devices.
  3. Air Filter Inspection: Check filter condition; recommend replacement if dirty.
  4. Blower Motor Inspection: Measure amp draw, listen for noise, and ensure smooth operation.
  5. Blower Wheel Cleaning: Remove debris buildup for optimal airflow.
  6. Capacitor & Contactor Check: Inspect and test starting and run capacitors, contactors.
  7. Electrical Connections: Tighten all terminal screws and inspect wiring for wear.
  8. Transformer Test: Verify primary and secondary voltages.
  9. Refrigerant Charge Verification: Measure pressures; adjust refrigerant to manufacturer specs.
  10. Refrigerant Leak Inspection: Check all joints and valves for signs of leaks.
  11. Indoor Coil Inspection: Look for dirt/damage; clean as needed.
  12. Outdoor Coil Inspection: Clear debris; perform a coil rinse if necessary.
  13. Drain Pan & Line Check: Flush condensate drain; verify proper slope and drainage.
  14. Condensate Pump Test: Ensure float switch and pump operation (if installed).
  15. Heat Exchanger Inspection: Examine for cracks, corrosion, or holes.
  16. Burner & Ignition Assembly: Clean burners; test ignition and flame sensor.
  17. Gas Pressure & Connections: Verify correct pressure and inspect for leaks.
  18. Flue Pipe & Venting: Check for obstructions and proper pitch.
  19. Combustion Analysis: Measure CO₂, CO, and stack temperature (gas systems).
  20. Static Pressure Measurement: Test duct static to ensure proper airflow balance.
  21. Ductwork Inspection: Visually inspect accessible ducts for leaks or damage.
  22. Airflow Testing: Measure supply and return airflow at registers.
  23. Fan & Belt Assessment: Inspect belts for wear/tension; lubricate pulleys.
  24. Heat Pump Reversing Valve Test: Cycle to heating and cooling modes (if applicable).
  25. Defrost Control Operation: Verify proper defrost cycle (heat pumps).
  26. Electric Heat Strip Test: Confirm operation of auxiliary heat elements.
  27. System Controls Check: Ensure proper sequencing of furnace/AC/heat pump stages.
  28. Voltage & Amperage Readings: Record on motors, compressors, and controls for baseline.
  29. Grounding & Bonding: Verify unit is properly grounded for safety.
  30. Overall System Run Test: Observe at least one full heat and cool cycle to confirm performance.

15‑Point System Inspection

  1. Thermostat Check: Verify set‑point accuracy and proper operation.
  2. Air Filter Inspection: Check filter condition and recommend replacement if needed.
  3. Electrical Connection Tightening: Inspect and tighten all electrical terminals.
  4. Capacitor & Contactor Test: Measure run/start capacitor values and inspect contactors.
  5. Blower Motor Function: Listen for noise, measure amp draw, and ensure smooth start‑up.
  6. Indoor Coil Inspection: Check for dirt and debris; clean lightly if accessible.
  7. Outdoor Coil Inspection: Remove leaves/debris and verify coil fins are straight.
  8. Refrigerant Pressure Check: Measure suction and discharge pressures to ensure proper charge.
  9. Drain Line & Pan Inspection: Flush condensate line and inspect pan for clogs or leaks.
  10. Fan & Belt Assessment: Inspect blower wheel and belts for wear; adjust tension as needed.
  11. Safety Control Test: Verify operation of limit switches and emergency shut‑offs.
  12. System Cycling Test: Run one complete heat/cool cycle to observe startup and shutdown.
  13. Airflow Verification: Measure airflow at a representative register to confirm adequate CFM.
  14. Ductwork Visual Check: Inspect accessible ducts for leaks, damage, or disconnections.
  15. Overall Performance Review: Record operating temperatures, pressures, and amp draws for baseline.